#Sainsmart dds140 pro how to
#Sainsmart dds140 pro install
#Sainsmart dds140 pro generator
#Sainsmart dds140 pro full
#Sainsmart dds140 pro pro

Also, it seems to have more than one life. If you are looking for something to work with low voltage, this will do fine for the DIY experimenter. Hooked it back up to the laptop and guess what? It began to work! Used it to check a circuit board with the 1mv test signal and it worked just fine. Went inside the DDS-120's box and took a look. SainSmart DDS140 The SainSmart DDS140 is a low-cost 2-channel, 200-MS/s.

Good for some that really know all the tricks to look for, but not good for this old farmer. With the addition of the BNC adapter and scope probes, professional or.

Even though I was set up for 50 volts with the probe, I missed something and even if I could get it repaired, I would not be comfortable using it. My opinion is that the five volts input max allows too much room for error. I am sticking with the little DSO-138, do the math, and make drawings. There must have been a load somewh ere even though the laptop was not plugged into AC. There was a little hiss inside the DDS-120 and it became a nice little paper weight. Using a DSO-138 oscilloscope to make sure everything was safe and the out put was a nasty looking DC at five volts., I put the probe on 10x, attached the ground to negative and touched the positive output. It was set up to check the DC out put from the rectifier into a load while the input AC was controlled.

#Sainsmart dds140 pro full

I decided to use it to check out a suspected full bridge rectifier from a welder so that I could compare the saved video with a known good rectifier. I really like that it did all the math and you could save the information. It checked out with my Heath Kit Oscilloscope calibrator.

#Sainsmart dds140 pro install

Choose Install from a list or specific location, and Next.Got the unit and set it up with a Dell e4300 laptop. Right-click My Computer to run the Device Manager, click Other Devices, and right-clickĢ. Turn the Time/DIV to 1ms, and the measured waveform will be displayed.ġ. You can use it to test, calibrate and set up the device:Ĭonnect one end of the probe to CH1 of the device, and the other end to the small metal tip The small metal tip between the two BNC ports will output a square wave signal of 1KHz withĪn maximum of about 3.3V. Turn on CH2, the waveform of Channel 2 will display.Ĥ. Click the Start button on the lower right corner, and it shows

#Sainsmart dds140 pro how to

You will find the driver under the folder “driver” in the software package.ĭetailed instructions on how to install driver on different OS are described in Chapter 4.1 and 4.2.ģ. Please unplug other USB devices in case of interference from its high current.Ģ. Windows will recognize it and have your computer to work with it.

#Sainsmart dds140 pro pro

1X SainSmart DDS140 Pro PC-Based USB Digital Storage Oscilloscopeġ.

The cap is commonly insulated with plastic and color-coded: red commonly means an active or positive terminal black indicates an inactive (reference or return) or negative terminal and green indicates an earth (ground) terminal. A binding post contains a central threaded metal rod and a cap that screws down on that rod. They are also found on loudspeakers and audio amplifiers as well as other electrical equipment. Within 1mm thickness sheet metal outer skin, the DDS oscilloscopes are effective in electromagnetic noise suppression and shielding.Ī binding post is a connector commonly used on electronic test equipment to terminate (attach) a single wire or test lead. Thicknesses can vary significantly extremely thin thicknesses are considered foil or leaf. Countless everyday objects are constructed with sheet metal.

It is one of the fundamental forms used in metalworking and it can be cut and bent into a variety of shapes. Sheet metal is metal formed by an industrial process into thin, flat pieces. As long as the SainSmart DDS140 Pro device via USB cable into your compute, it will form a complete oscilloscope test system after running the software. SainSmart DDS140 Pro body take operation of traditional oscilloscope operation and part function of display transfer drawing into the computer by the software to achieve.

#Sainsmart dds140 pro generator

When you do not want to spend a high price to buy a traditional oscilloscope, a signal generator and a logic analyzer. The highlighting advantages are the optional modular structure and high performance price ratio. It can be extended to achieve oscilloscope, signal generator and logic analyzer triple main functions by inserting different sub-modules. SainSmart DDS140 PC-Based USB Digital Storage Oscilloscope+Signal Generator SainSmart Due + 4.3' 4. SainSmart DDS140 Pro is a medium-performance oscilloscope.